Marantz DLP PROJECTOR VP-12S2 Manuale Utente

RModel VP-12S2 User GuideDLPTMProjector

6ENGLISHRemote Controlleradgl¡2¡5¡7™1¡1¡6shk¡0¡3¡4¡9¡8™0jfPROJECTORa POWER ON key (☞P.10)Turn the projector on.s STANDBY key (☞P.18)Turn the projector

7ENGLISH1. Open the Battery cover.2. Insert two AA size batteries.Make sure the polarities match the + and – marks insidethe battery compartment.3. Cl

8ENGLISH❖ When making connections be sure to:• Turn off all equipment before making any connections.• Use the proper cables for each connection.• Inse

9ENGLISHYou can connect this projector to HD-Video /PC using RGB IN port, or Satellite /Cable Tuner /PC using DVI-D IN port.1. Connect one end of the

10ENGLISH1. Connect the supplied AC power cord. (☞P.8)2. Press the POWER ON key on the remote controller or the POWER key on the projector.The POWER O

11ENGLISH❖ Turn the Lens Shift knob to counterclockwise : The image goes down.Adjust the height of the image by raising the projector with the adjustm

12ENGLISH2. Turn the Focus ring to make an adjustment.Adjust the focus for the sharpest image possible to obtain, using focus pattern.3. Press the FOC

13ENGLISH❖ Installing on a tabletop❖ Mounting on the ceilingCAUTION– For ceiling installation, consult with Marantz authorized dealer.– Do not look in

14ENGLISH❖ 16 : 9 ScreenIn case of displaying the 16:9 picture onthe whole of the 16:9 screen.❖ 4 : 3 ScreenIn case of displaying the 16:9 picture ont

15ENGLISHPress the POWER ON key on the remote controller or the POWER key on the projector.The POWER ON indicator lights up.Switch to the equipment co

WARRANTYFor warranty information, contact your local Marantz distributor.RETAIN YOUR PURCHASE RECEIPTYour purchase receipt is your permanent record of

16ENGLISH• Press the ZOOM key, the NORMAL key or the FULL key on the remote controller for the 4:3 aspect ratio video source.• Press the FULL key on t

17ENGLISH• Press the ZOOM key, the NORMAL key or the FULL key on the remote controller for the 4:3 aspect ratio video source.• Press the FULL key on t

18ENGLISH1. Press the STANDBY key on the remote controller or the POWER key on the projector.2. The fan continues to run for a while to reduce interna

19ENGLISHPicture AdjustContrastMain MenuItemMain MenuItem0 100Brightness 0 63Color 0 100Sharpness 0 31Tint R50 G50Noise Reduction 0 63Color Temp. (Tem

Refer to the on-screen menu for making various adjustments and settings. (☞P.19)1. Press the MENU key. The MENU appears.2. Use 3 / 4 / 1 / 2 keys to s

21ENGLISHBy adjusting this Fine Menu, you can make fine picture adjustment.Note : There are some parameters can not adjust according to input signal.❖

22ENGLISH❖ Sub ControlContrast Red: This menu allows the users to set the contrast for red.Contrast Green: This menu allows the users to set the contr

23ENGLISHThe following settings can be made:Aspect Full, Normal, Through, ZoomCinema Auto, OffCinema mode : The 3-2 pull down for NTSCand the 2-2 pull

24ENGLISHThe following adjustments can be made:– Keystone H, VAdjust trapezoid image to rectangle image.– Auto AdjustYes : For RGB IN signal, Picture

25ENGLISHThe following adjustments can be made:– OSD Position (16:9 / 4:3)Select OSD position from 16:9 or 4:3.– Reset Lamp LifeLamp Life must be rese

ENGLISHFOREWORDThis section must be read carefully before any connection ismade to the mains supply.WARNINGSEQUIPMENT MAINS WORKING SETTINGYour Marant

26ENGLISH❖ Setting the Config Menu1. Use 3 / 4 key to adjust.2. Use 1 key to go back to the menu item.Select either 12V output or 0V output by choosin

27ENGLISHThis unit has 4 picture modes, Theater, Standard, Dynamic, User, for your choice. You can choose one with the direction buttonson the unit or

28ENGLISH– When the lamp life becomes less than 100 hours and the unit is still on, the remaining lamp life is displayed on the screenautomatically.–

29ENGLISH1. Press the STANDBY key on the remote controller or thePOWER key on the projector to turn the projector off.2. After the cooling fan stops,

30ENGLISH8. Holding the handle and pull the lamp unit out toward yourside.9. Install a new lamp unit in position securely.10. Tighten the two screws o

31ENGLISHNo powerImage is not displayed.Poor color.Picture is too dark.Picture is not clear.Picture rolls.The Remote Controllerdoes not work.AC power

32ENGLISH❖ Optical characteristicsPanel 0.8 inch 16:91280 x 720 pixelsDigital Micromirror DeviceTMLamp Super High Pressure 150WLens f: 26.5 to 30.7 /

33ENGLISH❖ Timing chartNTSCPAL-B/GSECAM480/60p576/50p1035/60i1080/60i1080/50i1080/48i720/60p720/50p720/48p540/60p640x350#1640x350#1640x400#1640x400#16

34ENGLISHDIMENSIONSSTANDBYPOWER ONLENS SHIFTLAMPWARRNINGENTERFOCUSMENUPOWERLEFTRIGHTDOWNINPUTUPVP-12S2470 - 471 mm222.0 mm182.5 mm 82.615.0 - 61.8 m

Printed in Japan 09/2002 MITf 04AV851310is a registered trademark.RCOUNTRY COMPANY ADDRESSALGERIE Azur 2000 8, Lotissement Ben Hatadi, Alger, Alger

ENGLISHTABLE OF CONTENTSIMPORTANT SAFEGUARDS...

1ENGLISHThere is potential glass particle hazard if the lamp ruptures.There is a potential hazard of glass particle if the lamp ruptures.In case of la

2ENGLISHFEATURES❖ Optics• Texas Instruments DLPTM(Digital Light Processing)Technology• 1280 x 720 DMDTMPanel• 16 : 9 Aspect Ratio• Custom Optics Devel

3ENGLISH• Lens Cap x 1• Remote Controller x 1• AA Size Batteries x 2• AC Power Code x 1• Control Adapter Cable (Mini Jack to RCA) x 1• Scart - RCA plu

4ENGLISHFront and Top View321139 7 6 5 10 4 11 12 8IR sensorProjectionLensq Focus ring (☞P.10)Adjust the picture focus.w Zoom ring (☞P.10)Adjust the s

5ENGLISHRear and Terminals View1314Lamp coversecuring screwLamp coverIR sensor1 2 3 4 57 8 9 10 11Terminals6!4 AC IN (☞P. 8 )Connect the supplied AC p